Recommended gas pressure - Miller Welding Discussion Forums
2011年4月7日 · The manual for the Millermatic 200 does NOT give any info on shielding gas adjustments. All it says is that different gas mixtures have different requirments as far as pressure and flow. This is a good source of info.
Mig Gas Settings - Miller Welding Discussion Forums
2008年3月8日 · Excessive gas flow will not cause spatter, but it will burn up you wallet a lot faster. For CO2 15-20 cfh, if you are using mix gas or argon for short circuting somewhere between 25-35 cfh is a good starting point. If you want to get into spray transfer you are looking at a range of 45-55 cfh, as the arc is trasfered through the shielding gas only.
At what PSI should I set the regulator for MIG?
2005年3月28日 · If you're talking regulator (unrestricted low pressure outlet) vs. flowguage/meter (.032 orfice in dischsrge) I think I'd start around 6 PSI. That should be about 18SCFH on a flow meter. If you set the regulator at 20 - 25 PSI, the wind will knock over your workpiece. That's where I set my cutting oxygen. Hank
MIG gas regulator setting - Miller Welding Discussion Forums
2013年9月25日 · On a normal gas regulator, (ie. Acetylene) there are two gauges. One for tank pressure, other for line pressure. On a Mig regulator, there is tank pressure gauge and a flow meter. The line pressure gauge is missing. IF that line pressure gauge was there, what should the pressure be? I know that because of choked flow, the dynamic pressure
Recommended gas pressure - Miller Welding Discussion Forums
We get many questions about setting MIG gas pressure. Unlike with oxyfuel welding with MIG (or TIG) “flow” is set NOT pressure. Here is why: Having been in the welding business for over 40 years and having managed an R&D lab for a major industrial gas company, setting the proper gas “flow” is not well documented.
MM252 Recommended Mig settings for 3/16" steel joints?
2017年2月6日 · Not sure why, but the MM252 settings table for 3/16" steel 18.4V at 265 ipm contradict the Miller Mig welding calculator. by saying I'll need a LOT more wire feed speed? Short Circuit Transfer Wire Size & Wire Feed Speed:.035" (0.9 mm) at 320-340 ipm Shielding Gas & Voltage Range: 75% Argon/25% CO 2: 18-19 Volts
Multimatic 215 Mig Settings - Miller Welding Discussion Forums
2016年12月12日 · OK, got back in the garage Miller settings as recommend were 16.2 volts at 330 wfs , not useable... 17volts at 200 wfs to 18volts to 250 wfs is what seemed to work. Pretty far off from chart or machine. Anyone have similar settings with .023 or settings on 16 gauge from similar mig machine (millermatic, etc) Sandy
Millermatic 211 Settings - Miller Welding Discussion Forums
I have a 2020 Millermatic 211 and am working with gas shielded flux core Kiswel E71T-1C/1M .045 and gas shielded Stainless Steel Flux Cored Wire E308LT1 .035. I have done OK at dialing in the settings myeself. But it would be helpful if there was a reference for situations not listed on the welder door to help with getting started.
Adjusting the mig welder - Miller Welding Discussion Forums
I'm using a Millermatic 252 and am new to mig welding. I'm attempting my first welds on some 18 gauge steel, with settings of 17 volts and 260 ipm with .035 sc wire. I'm blowing through the metal and am looking for advice on what whether to try voltage changes or ipm first. I …
Gas Flow Settings MIG - Miller Welding Discussion Forums
2023年6月17日 · Typical flow rate for CO2 shielding gas and MIG (GMAW) welding is 15 to 30 CFH (cubic feet per hour) and mixed gas is 25 to 45 CFH. Typical flow rate for Argon shielding gas and TIG (GTAW) welding is 15 to 25 CFH and aluminum MIG (GMAW) welding is 35 to 45 CFH. Check wire manufacturer’s recommended flow rate.