Brazing brass using brass filler rods - Bladesmith's Forum Board
2012年7月26日 · Location:Omaha, Nebraska. Posted July 26, 2012. Adriaan, Using brass brazing rod to braze together several pieces of brass will likely result in a big puddle! Brass brazing is used to join together metals that have a higher melting temperature than that of the brass itself.
Help with a solder choice for brass Chape - Non-Ferrous: fittings ...
2020年2月13日 · Both are a 56% silver brazing rod, but the Safety-Silv is much smaller diameter than the SSF-6 I see on Amazon. It will not break. In fact, it will outlast the brass. It has a slight brassy color, and matches well when fresh, but when the brass eventually tarnishes the braze line will stand out like a sore thumb.
Brazing help - Tools and Tool Making - Bladesmith's Forum Board
2008年9月10日 · The brazing rod contains zinc and the zinc will boil off and raise the melting point of the brass, making it harder to braze the part. Instead heat the parts in the forge and when they are hot enough, pull them out and touch the brazing rod to the joint. The brass should melt and get sucked into the joint by capillary action.
Brass Pins to secure scales - Bladesmith's Forum Board
Posted February 6, 2009. I use the rivets to hold the scales, so I need them to fix them well in place. The way I do it is: - first mushroom one side of the pin while holding it in a vice. - cut the pin to about .5mm protruding at the other end. - use a ballpeen to gently tap down the edges of …
Handle help - Fit and Finish - Bladesmith's Forum Board
2022年8月13日 · Now you go by the alloy number, and pay no attention to the actual name. Jeweler's bronze is actually plain copper/zinc brass, naval forging brass is actually copper/tin bronze, and so on. Brazing rod is technically a bronze, but may be brass as well. If you want a really strong joint use a pre-1981 U.S. penny. Or a brass-looking key.
Koa, Copper, Brass, and Spring Steel - Show and Tell
2011年5月2日 · I finished this yesterday; steel is from a 1 inch coil spring salvaged from the scrapyard; forged from a 1 1/2 inch length (just wanted to see if I could do it) differentially quenched with local koa wood handle, copper spacer, and brazing rod pins. 8.5 inches overall length with a blade length of 4 1/8 " and width of 1 7/16"; I …
Making Scabbard Fittings - Bladesmith's Forum Board
2017年1月6日 · Funny you should mention this, I just got my butt kicked by a scabbard chape. I spent I bet 8 hrs on making this stupid thing, trashed a whole sheet of brass. I made a wood copy of the scabbard to form it on and did a small folded seam. (used all my oxgyn trying to braze up 3 flops) Im making the mouth of tooled leather.
Advice for Civil war dagger sheath - Sheaths and Leatherwork ...
2023年8月26日 · For cold-forming the brass, I usually forge it around a steel mandrel and make the parts in halves, then braze the seams. The late Alex Daniels made a neat-o press to do this. He'd grind out a steel mandrel the exact size of the sheath tip and throat, make a paper pattern that would fit perfectly halfway up the sides of the mandrels.
Not quite Hiltiprecht - Show and Tell - Bladesmith's Forum Board
2015年7月13日 · Ondrej, that's brilliant! I have been brazing the rivets after setting them in the holes by heating, THEN applying hard silver solder in wire form, and the cleanup is a pain. I will use this method from now on. Thanks!
Kilij-style knife? Just finished today. - Bladesmith's Forum Board
2024年4月11日 · Some more of my Things Made This Month...a stacked leather/brass/micarta single-edge dagger a la scian-dubh and sheath, French-style sabatier in 80crv2 and patnered meat cleaver in 1084 with cocobolo, brass corby's and dovetailed bolsters with (respectively) cherry and walnut scabbards, and an ebony and copper hunter from 80crv2 with the best hamon I've accomplished yet.