is a 268xp really better than a regular 268?
2016年10月13日 · (µ/ý X¤K :™ÙID gFã ! ©¥õÏï•-Z!;bI:EJÌÈ~>žE¨kiq®Uª5Š«' ÏïÇ dòÕ£ =ßk€„2By… „ s þ7:²«Æ}½âÀ Yœ±Í 4ˆ¥C†®ºNŒ£› t 4R‹ŽÃ A ]eéN×Xè Ù‹nA3¹â‹^õ LmæÍB[{ aSçªGhÌ'Zú+Ð_™7› ¡ ¦i˜Æ¡a±àÂ…†x±ãò¥[Jɶ¾F ‚,ËY úå²WÇ«ª‚ (øütÓltܤò Yt ×^NÃôù PúpmŽO_ârŸ{À‰ ¤[ú‘û–ÆUÊ×)# ...
Husqvarna 268 oiler adjustment - Arborist, Chainsaw & Tree Work …
2015年6月18日 · The 268 has a 4 position screw adjustment to regulate oil volume. Remove the clutch cover. The adjustment screw is flush with the pump around the 10 o'clock position behind the clutch hub. You may need to clean the gunk before it becomes visible. There are 1-4 numbers cast into the pump around the slotted screw. One is least flow, four is max flow.
husqvarna 268 open port cyl vs 266xp cyl... - Arborist, Chainsaw
2010年12月12日 · I have a January 1993 Husqvarna Forest and Garden catalogue with models 266xp and 268 non xp specs. Both saws have a cylinder displacement of 67cc and 4.1 cu. in. The engine horsepower on the 266xp is 4.5 HP and the 268 is 4.6HP. The 266xp max rpm's are 12,500 and the 268 max is 13,300. The 266xp weighs 13.5 pounds and the 268 weighs 13.6 …
Please explain the diff between husky 268, 272, and 272xp
2008年1月9日 · 66/266/268-50mm piston 272-52mm piston They all have the same stroke and all fit the same case. The transfer ports are different in the some of the cylinders. Some of the 266's have open transfers. The 268and the 272 have closed ports. The top cover screw holes (in the case) for the 61 do not match the screw holes for a 268/272 cover.
Husqvarna 162 61 262 266 268 272 parts interchangeable?
2011年8月1日 · Never seen PTO side crank seal mounted in the case on this series, always in the oil pump. As far as swapping cylinders the stroke and bolt pattern is the same on all of them so it is doable but you have to be mindful of your intake stuff, (four versions, 625 & 670 JRed boot, 61 block, 162/630/66/266 block, and 268/272 block).
Husqvarna 268 chainsaw - Arborist, Chainsaw & Tree Work Forum
2014年2月23日 · hello looking a getting another saw in the mid power range close to the 61 model.and i was looking at maybe the 268 model. wanting to run a 24-28" bar max on it cause i all ready have a 395xp for my big saw. just want something like the 61. dont really want a stihl either Im pretty loyal to the husky saws.
Husqvarna 268 & 266XP - Arborist, Chainsaw & Tree Work Forum
2020年2月16日 · The 268 is an open port saw, same cylinder as the 66. The 268xp is closed port like the 266, but there are porting differences as well as the filter/carb. All are the same displacement.
262 vs 266 vs 268 - Arborist, Chainsaw & Tree Work Forum
2009年6月11日 · I'm sure the 266 is a 2 piece unit. If the 268 is a 1 piece coil I would build it over the 266. Parts are easier to find and the 272xp top end will bolt on and fit under the stock covers. although it is heavier than your old 262xp the 272xp top end on the 268 crankcase will have more hp than a 262 ever thought of.
husqvarna 268 questions | Arborist, Chainsaw & Tree Work Forum
2010年8月19日 · Yes they did make a 268 with open ports and a flatside (nonwindowed) piston. These P&Cs were made by Gilardoni. These were the last version of the 268 and they were detuned and dropped the XP designation. They only made the 268 in the XP version until they made this change. The straight 268 appeared around the time they introduced the 272XP.
Hard to pull thru husqvarna 268 - Arborist, Chainsaw & Tree Work …
2017年8月26日 · Can't start the husqvarna 268. Seems compression is super high so I can't pull the starter thru. If I take out the plug then it pulls thru fine. See the video. What is keeping it from pulling thru?